Penetration Bitumen Grades

Penetration Bitumen 10/20 | Bitumen 10/20

Product Overview

Penetration Bitumen 10/20 (also called bitumen 10/20, hard paving grade bitumen 10/20 or hard bitumen 10/20) is a hard-grade paving bitumen produced from vacuum residue in crude oil refining. The grade name refers to its needle penetration at 25 °C of 10–20 dmm (tenths of a millimetre); its softening point is 65–75 °C and its specific gravity is 1.01–1.06.

Its low penetration gives asphalt mixtures very high stiffness and strong resistance to rutting under heavy loads and high temperatures. Hard grades such as 10/20 are widely used in base and binder courses of high-modulus asphalt, where the higher stiffness allows thinner structural layers than conventional bitumen. Typical uses include heavy-duty highways, airfields and pavements in hot climates.

Pars Universal Bitumen (PUB-Ltd) supplies Penetration Bitumen 10/20 in new steel drums, jumbo bags and bulk, with worldwide shipping. See the technical data sheet below or contact us for a free quote.

Penetration Bitumen 10/20 Technical Properties

Penetration Bitumen grades are named according to the penetration degree of the needle into the bitumen. According to this information, Penetration Bitumen 10/20 has a penetration grade between 10 and 20 desi-millimeters; also its softening point is in the range of 58 to 60 °C. Moreover, it should be mentioned that all grades of this category have thermoplastic properties, the same as synthetic resin materials, which get softer by heating up and become more complicated by heating down.

Penetration Bitumen 10/20 Applications

The primary purpose of using this grade is to combine it with the hot asphalt mixture in asphalt production plants. This grade is used in bases, coating patches and routes, pavements, road construction and repair operations. Moreover, it can save costs and materials used more than 30 percent compared to traditional methods.

Hazards and Handling

The main hazards presented by Asphalt relate to the temperature of the material. If the asphalt material is hot, it may burn the skin.

Hot Asphalt 10/20 may release fumes that are not hazardous in open air situations, but continuous inhalation of high vapor concentrations in poorly ventilated, closed or semi-closed areas may cause health risks.

Although asphalt is not normally a dusty material, dust may be released during drilling, cutting or shoving hardened asphalt. If it is inhaled in excessive amounts over an extended period, dust can constitute a health hazard.

Inhalation of fumes should be avoided as far as is reasonably practicable. Skin contact with the hot product may cause burning of the skin, therefore should be avoided. If there is a risk of vapor formation, then additional ventilation should be maintained.

Asphalt should be handled away from sources of ignition and heat. Smoking, eating or drinking during its use should be avoided.

Storage

No special requirements. Asphalt 10/20 is normally used upon receipt. Refer to the relevant Technical Data Sheet for the specific product. Packing New Steel Drum, Jumbo Bag, Bulk.

FAQs about Penetration Bitumen 10/20

Q: What is penetration bitumen 10/20?
A: Penetration bitumen 10/20 is a hard paving-grade bitumen with a needle penetration of 10–20 dmm at 25 °C and a softening point of 65–75 °C. It is used where high stiffness and rutting resistance are needed.

Q: What is the difference between bitumen 10/20 and 60/70?
A: Bitumen 10/20 is much harder than 60/70 (penetration 10–20 dmm versus 60–70 dmm) and has a higher softening point. It is used for heavy-duty, high-stiffness base courses, while 60/70 is a general-purpose paving grade.

Q: Where is bitumen 10/20 used?
A: It is mainly used in base and binder courses of high-modulus asphalt for highways, airfields and heavy-traffic or hot-climate pavements.

Q: How is penetration bitumen 10/20 packed?
A: In new steel drums, jumbo bags and bulk.

Penetration grade bitumen 10/20

Technical Data Sheet

Get a personalized quote for your specific requirements by writing to us at [email protected] or simply filling out the inquiry form here.

Last reviewed: November 2026

Property Test Method Unit Specification
Specific Gravity @ 25/25 °C ASTM D70/D70M – 1.01 – 1.06
Penetration @ 25 °C ASTM D5/D5M 0.1 mm 10 – 20
Softening Point (Ring & Ball) ASTM D36/D36M °C 65 – 75
Ductility @ 25 °C ASTM D113 cm 5 min
Loss on Heating ASTM D6/D6M % wt 0.5 max
Drop in Penetration after Heating ASTM D6/D6M & D5/D5M % 25 max
Flash Point (Cleveland Open Cup) ASTM D8254 °C 250 min
Solubility in Trichloroethylene or Toluene ASTM D2042 % wt 99 min
Matter Insoluble in Trichloroethylene or Toluene ASTM D2042 % wt 1 max
Spot Test AASHTO T 102 – Negative

Have any questions or concerns, or need more information? Reach out to our team at [email protected]

You can contact our team for more detailed explanations. We are here to help you.

Our professional team offers you the most suitable products for your projects with quality and reliability.

Penetration Bitumen 10/20, Bitumen 10/20